-
Match the complete marking
Include the complete 330908-00-20-10-02-05 marking and photographs of the installed connection and mounting position.
-
Check the offered item before ordering
Request available-unit label and connector photographs. Have your maintenance team compare the offered 330908-00-20-10-02-05 with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 330908-00-20-10-02-05
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:330908-00-20-10-02-05
-
Weight:0.05 kg
-
Tariff Code:8537101190
-
Probe family:3300 XL NSv
-
Unthreaded length:0.0 in
-
Overall case length:2.0 in
-
Total probe length:1.0 m
-
Connector and cable option:02 - ClickLoc, standard cable
-
Agency approval option:05 - Multiple approvals
-
Probe thread:3/8-24 UNF-2A
-
Probe construction:Standard mount, without armor
-
Cable construction:75 ohm triaxial, FEP insulated
-
System linear range:1.5 mm (60 mils), matched NSv system
-
System scale factor:7.87 V/mm (200 mV/mil)
-
Recommended gap:1.0 mm (40 mils)
-
Frequency response:0 to 10 kHz, +0/-3 dB typical
-
Recommended flat target:13 mm diameter minimum
-
Minimum cable bend radius:25.4 mm
Information
- The zero-unthreaded body and unprotected ClickLoc joint define a compact NSv execution for restricted-clearance measurement points.
Small-target measurement: NSv system geometry supports reduced shafts and targets when the documented spacing rules are applied.
Direct service connection: The standard ClickLoc joint remains accessible without a factory-installed protector.
The 1.0 m standard triaxial lead ends in a ClickLoc connector without a factory-installed protector. Routing and environmental protection must therefore be reviewed for the actual probe-to-extension joint.
NSv range and scale values apply to a matched probe, extension cable and Proximitor Sensor. Small-target and tight-counterbore installations require additional attention to gap, shaft diameter and cross-talk during commissioning.
330908-00-20-10-02-05 Official Datasheet Excerpt
Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet 147385 Rev. R. Selected original pages covering the applicable product family, technical data and ordering information.330908-00-20-10-02-05 Installation & Verification Guide
Apter Power field guide covering identity capture, installed relationships, controlled replacement, commissioning and handover.
Application scope: Apply it where the zero-unthreaded 2.0 in body and NSv small-target performance match the approved machine drawing.
Compact threaded ports
Use the flush 3/8-24 case where the machine geometry does not require an unthreaded reach.Small target measurements
Review the documented flat-target diameter and scale-factor effects before acceptance.Restricted side-view locations
Use the NSv body where standard 8 mm probe clearance is insufficient.Phase and speed reference
Confirm target feature and the receiving-channel range before using the probe for timing duty.
Do not substitute a visually similar long-reach 330908 execution.
Confirm the installed thread and locknut geometry against the drawing.
Option 02 has no factory-installed protector; apply the approved environmental protection separately if required.
Small targets and tight counterbores can change scale factor at far gaps.
Maintain documented tip separation or approved axial offset on small shafts.
Set gap and compare the restored channel with its accepted baseline.
Alternative Names
Technical notes
Exact configuration: 3/8-24 UNF NSv probe without armor, 0.0 in unthreaded length, 2.0 in case, 1.0 m standard lead and multiple approvals
Connector boundary: Option 02 does not include a factory-installed connector protector
Technical reference: Bently Nevada 3300 XL NSv Proximity Transducer System Datasheet 147385 Rev. R
FAQ View All FAQ
-
What does zero unthreaded length mean for 330908-00-20-10-02-05?The 3/8-24 thread begins directly behind the sensing end, so port depth and locknut position establish the final tip location.
-
How should the 2.0 in case of 330908-00-20-10-02-05 be checked?Confirm the complete threaded-port depth, engagement and target clearance rather than matching only the thread diameter.
-
Is a connector protector included with 330908-00-20-10-02-05?No. Option 02 is the standard ClickLoc cable without a protector; add only the approved protection needed by the installed environment.
-
What small-target limit applies to 330908-00-20-10-02-05?A 13 mm flat target is recommended; smaller targets can change scale factor and require closer application review.
-
How can cross-talk be reduced for 330908-00-20-10-02-05 on a small shaft?Maintain the NSv tip separation guidance or use the documented axial offset arrangement while preserving required measurement travel.
-
Which electrical length begins with 330908-00-20-10-02-05?The probe contributes 1.0 m; the extension cable and Proximitor Sensor must complete the intended NSv system length.
-
How is 330908-00-20-10-02-05 proven after installation?Set the approved live gap, observe stable bias and compare runout, vibration, position or phase response with the prior channel record.
-
What approval information accompanies 330908-00-20-10-02-05?Code 05 selects the documented multiple-approval option; use the applicable certified installation drawing for the actual circuit.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
330908-00-20-10-02-05Product Details -
330104-00-04-10-02-00Product Details -
330905-00-08-05-02-05Product Details -
330104-00-24-10-02-00Product Details -
330104-10-19-10-02-00Product Details -
330103-00-19-10-12-05Product Details -
330104-00-06-10-02-05Product Details -
330104-04-10-05-01-00Product Details -
330103-17-22-10-12-05Product Details -
330103-00-08-10-12-05Product Details
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






