How is the channel recommissioned after installing 330703-000-050-10-02-00?

Restore the matched loop, verify supply and bias voltage, prove movement through the expected linear region and test the configured alarm or trip response under controlled conditions.

Can 330703-000-050-10-02-00 be mixed with another probe family?

Use only combinations explicitly permitted by the 3300 XL 11 mm Proximity Transducer System documentation; connector fit alone does not establish electrical calibration or interchangeability.

What maintenance condition should trigger inspection of 330703-000-050-10-02-00?

Inspect the assembly after cable impact, connector contamination, abnormal bias voltage, unstable vibration, loss of linear response or any work that changes the probe mounting.

Which Bently Nevada transducer system uses 330703-000-050-10-02-00?

330703-000-050-10-02-00 belongs to the 3300 XL 11 mm Proximity Transducer System and must be combined only with the probe, extension cable and Proximitor Sensor arrangement documented for that system.

How should engineers confirm the system length for 330703-000-050-10-02-00?

Add the installed probe lead and extension-cable lengths, then compare the total with the matching Proximitor Sensor length before energizing the channel.

What connector checks are required for 330703-000-050-10-02-00?

Inspect both mating surfaces for contamination or damage, align the ClickLoc connector correctly and tighten it finger-tight until the locking action is complete.

How should 330703-000-050-10-02-00 be routed in a machinery enclosure?

Maintain the documented bend radius, provide mechanical support and keep the cable away from sharp edges, hot surfaces and locations that can impose tensile load.

What must be recorded before replacing 330703-000-050-10-02-00?

Record the full catalog marking, mounting position, companion component numbers, cable route, monitor channel, static gap and as-found polarity.

Bently Nevada 330703-000-050-10-02-00 3300 XL 11 mm metric proximity probe

Name: 330703-000-050-10-02-00
Brand: Bently Nevada
SKU: 330703-000-050-10-02-00

330703-000-050-10-02-00

3300 XL 11 mm metric proximity probe

In Stock

Ships by Friday, September 18

Fast Shipping Available

Technical specifications for 330703-000-050-10-02-00

Manufacturer:

Bently Nevada

Product Category:

Machinery Monitoring System

Spare Part Number:

330703-000-050-10-02-00

Estimated shipping dimensions:

2.5x2x115cm

Weight:

0.1 kg

Tariff Code:

8537101190

Counliy of origin:

USA

Probe thread:

M14 x 1.5

Cable armor:

None

Unthreaded length:

0 mm

Overall case length:

50 mm

Total probe length:

1.0 m

Connector:

Miniature coaxial ClickLoc

Connector protector:

Not included

Agency approval option:

Probe resistance:

5.9 +/- 0.5 ohm

Probe tip material:

PPS

Probe case material:

AISI 304 stainless steel

Cable impedance:

75 ohm triaxial

Minimum bend radius:

25.4 mm (1.0 in)

Recommended case torque:

21.1 N m (187 in lbf)

Information

Overview Manuals Common Applications Product Precautions

Bently Nevada 330703-000-050-10-02-00 is 3300 xl 11 mm metric proximity probe. It is a compact 50 mm case probe for non-contacting displacement and vibration sensing in a matched 3300 XL 11 mm loop.

Fits a 50 mm overall case envelope
Uses an M14 x 1.5 mounting thread
Connects through a one-metre standard lead
Provides long-range eddy-current measurement

330703-000-050-10-02-00 is installed with five-metre 3300 XL 11 mm Proximitor Sensor, four-metre 330730 extension cable, threaded probe mounting bracket, compatible position or vibration monitor.

Engineered applications include Tight-clearance axial position loops, Differential-expansion channels, Large-journal vibration monitoring, Turbine proximity-loop modernization.

Important Notice: Check the 50 mm case envelope and thread engagement before installation, secure the probe without twisting its lead, complete the five-metre matched loop and confirm the required static gap and monitor polarity.

Apter Power 330703-000-050-10-02-00 Manuals and Guides

Apter Power 330703-000-050-10-02-00 Product Technical Reference PDF 330703-000-050-10-02-00 Engineering Installation and Verification Workbook

The first document presents model-specific technical identity and engineering data. The second provides a separate installation, connection and commissioning workflow.

Tight-clearance axial position loops

330703-000-050-10-02-00 supports this documented 3300 XL 11 mm Proximity Transducer System engineering task.

Differential-expansion channels

330703-000-050-10-02-00 supports this documented 3300 XL 11 mm Proximity Transducer System engineering task.

Large-journal vibration monitoring

330703-000-050-10-02-00 supports this documented 3300 XL 11 mm Proximity Transducer System engineering task.

Turbine proximity-loop modernization

330703-000-050-10-02-00 supports this documented 3300 XL 11 mm Proximity Transducer System engineering task.

Read the applicable Bently Nevada instructions before work. Verify 330703-000-050-10-02-00 and the installed-system configuration.

Verify the complete 330703-000-050-10-02-00 marking and its documented 3300 XL 11 mm Proximity Transducer System position before field work.

Place the monitored machine and associated protection channel in the approved maintenance state before disconnecting 3300 XL 11 mm metric proximity probe.

Protect every exposed connector and cable end from oil, moisture, dirt and impact while 330703-000-050-10-02-00 is open.

Record probe, extension-cable and Proximitor Sensor identities so the calibrated system length is preserved.

Route 330703-000-050-10-02-00 without sharp bends, crushing, abrasion or tensile loading at either coaxial termination.

Clean and finger-tighten each ClickLoc connection; never transfer connector torque or wiring practice from a different transducer family.

Set the static gap only after mechanical mounting and the complete matched loop have been confirmed.

Verify polarity, dynamic response and alarm action before returning the machinery-protection channel to service.

FAQS

How is the channel recommissioned after installing 330703-000-050-10-02-00?

Restore the matched loop, verify supply and bias voltage, prove movement through the expected linear region and test the configured alarm or trip response under controlled conditions.
Can 330703-000-050-10-02-00 be mixed with another probe family?

Use only combinations explicitly permitted by the 3300 XL 11 mm Proximity Transducer System documentation; connector fit alone does not establish electrical calibration or interchangeability.
What maintenance condition should trigger inspection of 330703-000-050-10-02-00?

Inspect the assembly after cable impact, connector contamination, abnormal bias voltage, unstable vibration, loss of linear response or any work that changes the probe mounting.
Which Bently Nevada transducer system uses 330703-000-050-10-02-00?

330703-000-050-10-02-00 belongs to the 3300 XL 11 mm Proximity Transducer System and must be combined only with the probe, extension cable and Proximitor Sensor arrangement documented for that system.
How should engineers confirm the system length for 330703-000-050-10-02-00?

Add the installed probe lead and extension-cable lengths, then compare the total with the matching Proximitor Sensor length before energizing the channel.
What connector checks are required for 330703-000-050-10-02-00?

Inspect both mating surfaces for contamination or damage, align the ClickLoc connector correctly and tighten it finger-tight until the locking action is complete.
How should 330703-000-050-10-02-00 be routed in a machinery enclosure?

Maintain the documented bend radius, provide mechanical support and keep the cable away from sharp edges, hot surfaces and locations that can impose tensile load.
What must be recorded before replacing 330703-000-050-10-02-00?

Record the full catalog marking, mounting position, companion component numbers, cable route, monitor channel, static gap and as-found polarity.

Individual privacy preferences

We use cookies and similar technologies on our website and process your personal data (e.g. IP address), for example, to personalize content and ads, to integrate media from third-party providers or to analyze traffic on our website. Data processing may also happen as a result of cookies being set. We share this data with third parties that we name in the privacy settings.

The data processing may take place with your consent or on the basis of a legitimate interest, which you can object to in the privacy settings. You have the right not to consent and to change or revoke your consent at a later time. This revocation takes effect immediately but does not affect data already processed. For more information on the use of your data, please visit our privacy policy.

Below you will find an overview of all services used by this website. You can view detailed information about each service and agree to them individually or exercise your right to object.

You are under 14 years old? Then you cannot consent to optional services. Ask your parents or legal guardians to agree to these services with you.

330703-000-050-10-02-00

Product Describe：

Ask our team:

Warranty Policy

Return Notice

Shipping Method

Parts Availability

How to order

Technical specifications for 330703-000-050-10-02-00

Technical specifications for 330703-000-050-10-02-00

Information

Information