Bently
View products
Product image is representative; revision or series may vary. Contact us to request a specific version.
Get a quick price for 16925-30
For more information on how your data is processed and stored by Apterpower please read our privacy policy
Technical specifications for 16925-30
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:16925-30
-
Estimated shipping dimensions:26x26x2.5cm
-
Weight:0.34 kg
-
Tariff Code:8537101190
-
Counliy of origin:USA
-
Cable construction:3-conductor shielded
-
Conductor size:22 AWG / 0.5 mm2
-
Sensor-end connector:3-socket plug
-
Monitor-end termination:Terminal lugs
-
Ordered length:30 ft
-
Approximate metric length:9.1 m
Information
Overview
Manuals
Common Applications
Product Precautions
Bently Nevada 16925-30 is a 30 ft three-conductor shielded accelerometer interconnect cable. It connects a compatible accelerometer to its monitoring input.
- Carries accelerometer power, bias, and dynamic signal conductors
- Connects the sensor plug to individual monitor terminals
- Maintains a shielded signal route over a thirty-foot run
- Supports fixed industrial routing between machinery and cabinet
16925-30 installs with compatible Bently Nevada accelerometer, monitor input terminals, field cable supports, approved shield termination in an engineered Bently Nevada acceleration transducer accessories configuration.
The commissioning workflow covers installed-hardware matching, controlled start-up and functional verification for this 30 ft accelerometer interconnect cable.
Important Notice: Confirm the complete 16925-30 marking, installed-system configuration, field connections and controlled functional test before commissioning or replacement.
Apter Power 16925-30 Manuals and Guides
Apter Power 16925-30 Product Technical Reference PDFBently Nevada 16925-30 Official Manual PDF
The first document is an Apter Power model-specific technical reference. The second supports model-specific installation, configuration and engineering verification.
Turbine casing acceleration monitoringCarries accelerometer power, bias, and dynamic signal conductors
Pump bearing-housing vibrationConnects the sensor plug to individual monitor terminals
Compressor accelerometer connectionMaintains a shielded signal route over a thirty-foot run
Motor and gearbox condition monitoringSupports fixed industrial routing between machinery and cabinet
Read the applicable Bently Nevada installation instructions before work. Verify 16925-30 and the installed Bently Nevada acceleration transducer accessories configuration.
1Verify 16925-30 and the 30 ft length before routing.
2Isolate the associated accelerometer input.
3Inspect the three-socket plug, cable jacket, and terminal lugs.
4Support the run so its weight cannot load the sensor connector.
5Keep the shielded cable separated from high-current conductors.
6Preserve conductor identity and the approved shield termination.
7Check continuity and insulation before reconnecting the monitor.
8Verify sensor bias and controlled vibration response before service.
Technical notes
Identify all three conductors and shield before replacement, support the 30 ft run, and verify continuity, insulation, sensor bias, polarity, and vibration response after reconnection.
FAQ View All FAQ
-
What should be checked if 16925-30 reports an unstable or incorrect value?Check seating, supply, grounding, shielding, matched components, mechanical installation, and the signal path before changing configuration or replacing additional hardware.
-
Can 16925-30 be replaced by a visually similar model without review?No. Verify the complete part number, electrical execution, connector arrangement, companion hardware, and approved software or rack configuration.
-
What commissioning evidence should be retained for 16925-30?Retain the full 16925-30 identity, as-left wiring and settings, measured functional-test results, final diagnostics, and authorization to return the affected equipment to service.
-
Which installed hardware must be matched before fitting 16925-30?Match the complete 16925-30 marking to compatible Bently Nevada accelerometer and monitor input terminals, then confirm the assigned Bently Nevada acceleration transducer accessories position and approved system configuration.
-
How should the field connections for 16925-30 be recorded before replacement?Record terminal or connector identity, polarity, shield, cable tag, channel assignment, and the as-found diagnostic state before disconnecting 16925-30.
-
What isolation is required before installing 16925-30?Place turbine casing acceleration monitoring in the approved maintenance state, isolate every applicable power, signal, and stored-energy source, and prove the work area safe.
-
Which configuration check is essential when commissioning 16925-30?Restore only the approved model-specific channel, range, address, scale, or interface settings and compare them with the physical installation before enabling the process function.
-
How can an engineer function-test 16925-30 after installation?Apply a controlled input, reference, or limited output appropriate to 30 ft accelerometer interconnect cable, observe the system indication and diagnostics, and confirm the intended process response.
Manufacturers
Supporting new and legacy automation
Whether you're maintaining existing equipment or sourcing parts for current systems, we provide fast, dependable supply you can rely on.
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
PRODUCTS IN SEARCH PAGE ()
50+ account managers available now
Manufacturers
You May Also Like
Explore related automation components available through Apter Power.
Manufacturers
Product Browsing History
Revisit the products you recently viewed on Apter Power.
SPEAK TO OUR TEAM
Let’s find the right solution for you.
Send us the part number, quantity and delivery destination. Our team will help confirm availability and lead time.
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.