With more than 30.000 high-quality spare parts, they can be sold immediately. Our large inventory allows us to quickly meet customer needs, thereby reducing downtime and protecting production schedules. Our timely delivery time provides you with security and save money.
3-conductor shielded 22 AWG (0.5 mm²) armored cable with
3-socket plug at one end, terminal lugs at the other end
Minimum length of 3.0 ft (0.9 m)
maximum length of 99 ft (30m)
The 16710-18 is an 18-foot (approximately 5.5-meter) 3-conductor shielded cable utilized to transmit analog signals from 330400 and 330425 Accelerometers to machinery protection monitors or field junction boxes.
Physical Tolerance in High-Temperature and Chemical Environments
Physical Ruggedness against High Temperatures and Chemical Exposures
Strict explosion protection compliance in hazardous areas
The mechanical interface at Side A incorporates an environmentally sealed, threaded 3-pin MIL-C-5015 connector equipped with an internal fluoroelastomer sealing boot, ensuring a gas-tight, moisture-proof IP66 connection when fully torqued onto the mating receptacle of the accelerometer sensor body.
The Fluorinated Ethylene Propylene (FEP) outer jacket and internal conductor insulation provide continuous non-degrading performance when exposed to industrial lubricants, synthetic turbine oils, water accumulation, and ultraviolet (UV) radiation, supporting stable mechanical properties within a temperature limit of -55°C to +200°C.
Side B terminates in a blunt-cut (pigtail) format with stripped wire ends, allowing direct termination into DIN-rail terminal blocks located inside field junction boxes or structural instrument enclosures.
Electrically, the capacitance, inductance, and resistance parameters per unit length of this assembly remain compliant with parameters required for intrinsically safe (I.S.) circuit loop validation when connected via approved zener barriers or galvanic isolators in hazardous industrial environments.
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Bently Nevada 16710-18 Interconnect Cable Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Petrochemical & Refining
Transmitting casing vibration signals of heavy-duty hydrotreating compressors and hot oil pumps in catalytic cracking units with temperatures up to 200°C.
Thermal Power Generation
Routed along high-temperature bearing housings of boiler feedwater pumps, induced draft fans, and high-pressure circulating water pumps for condition monitoring.
Nuclear Power Generation
Applied for signal connections of vibration sensors on main feedwater pumps and auxiliary feedwater pumps located in the conventional island area.
Hydroelectric Power Generation
Connecting casing absolute vibration sensors on upper guide and thrust bearing housings of vertical hydro-generator units under moisture environments.
Steel & Metallurgy
Resisting high thermal radiation to connect case accelerometers on blast furnace blowers, large exhaust fans, and sinter plant main gearboxes.
Coal Chemical & Fertilizers
Routing high-frequency casing vibration data from syngas compressors and high-pressure fertilizer pumps out of hazardous areas containing corrosive gases.
When using the 16710-18 interconnect cable, routing must strictly adhere to the 48 mm minimum bend radius limit, avoiding sharp bends, excessive pulling, or mechanical abrasion against sharp edges to safeguard the shield and inner conductors.
During sensor-side installation, the MIL-C-5015 threaded connector must be aligned and torqued properly to achieve an IP66 gas-tight seal, while the overall shield must be single-point grounded at the field junction box or monitor side and left floating and insulated at the sensor side to prevent electromagnetic interference from ground loops.
Alternative Names
Alternative Names
1671O-1816710-46I67I0-18I67IO-18
Technical notes
Technical notes
The Bently Nevada 16710-18 Interconnect Cable is an 18-foot (approximately 5.5-meter) 3-conductor shielded analog signal cable utilized for connecting 330400 and 330425 accelerometers. Its physical construction consists of 22 AWG stranded copper conductors, an overall metal shield layer, and an FEP jacket, providing an operating temperature range from -55°C to +200°C for continuous service in water and oil environments. Side A features a 3-pin MIL-C-5015 sealed connector achieving an IP66 rating when mated, while Side B is blunt cut; its electrical parameters support service in hazardous areas when paired with safety barriers.
It is an industrial-grade 3-conductor shielded interconnect cable used to transmit analog vibration signals between accelerometers and monitoring systems.
What materials are the jacket and insulation of 16710-18 made of?
Its jacket and insulation are made of Fluorinated Ethylene Propylene (FEP), providing chemical resistance.
How to use products like 16710-18?
Thread the end with the MIL connector tightly onto the sensor, and connect the blunt-cut end into a field junction box or monitoring instrument terminals.
Which sensor models are compatible with 16710-18?
It is specifically compatible with 330400 and 330425 Accelerometers.
What is the structure and specification of the internal conductors?
It contains three 22 AWG stranded copper conductors wrapped in an overall shield layer.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, modules and cards, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer`s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Videos
News
Applications
