-
Match the complete marking
Include 146031-01 and every revision or approval marking visible on the item. Keep the exact reference on your enquiry and quotation. -
Check the offered item before ordering
Request available label and interface photos. Have your maintenance team compare the offered 146031-01 reference with the installed equipment and applicable Bently Nevada documentation.
Technical specifications for 146031-01
-
Manufacturer:Bently Nevada
-
Product Category:Machinery Monitoring Systems
-
Spare Part Number:146031-01
-
Weight:0.4 kg
-
Tariff Code:8537101190
-
Ethernet interfaces:1 copper interface
-
Supported Ethernet:10Base-T and 100Base-TX
-
Connector:RJ-45
-
Cable category:Shielded Category 5
-
Fiber interfaces:0
-
Standard cable lengths:1.8 to 97.5 m in listed assemblies
-
Rack position:Rear I/O slot
-
Front-module pairing:1 TDI front module
Information
- The complete 146031-01 identity establishes the hardware selection; installation still depends on the documented host, companion components and project configuration.
Front/rear pairing: The rear I/O module must remain paired with the corresponding 3500/22M TDI slot.
Network-record control: Retain IP, port, switch and System 1 communication records before replacement.
The -01 hardware uses 10Base-T/100Base-TX copper cabling; the -02 variant is a fiber interface. Connector fit and part-family similarity do not make those network media interchangeable.
Commissioning should verify physical link, TDI rack communication, configured network identity and System 1 data transfer. Record switch port, cable label and diagnostic state with the as-left rack configuration.
-
Bently Nevada 146031-01 technical reference
Apter Power reference with verified manufacturer data and exact-model applicability. -
Bently Nevada 146031-01 engineering guide
Apter Power installation, configuration, diagnostic and acceptance guidance.
Platform applications: The uses below depend on the installed controller configuration and approved system design.
-
3500 rack Ethernet communication
Connect a 3500/22M TDI to the approved copper plant network. -
System 1 data transfer
Carry rack data to configured condition-monitoring software. -
Transient data access
Support communication required for transient and steady-state data collection. -
TDI rear-I/O replacement
Restore an exact copper interface without changing rack or network media.
Match every field of 146031-01 with the approved spare-parts record before installation.
Use grounded handling, antistatic packaging and protected work surfaces for exposed electronics.
Confirm connector keying, slot assignment, supply and companion hardware before energizing.
Record switches, firmware, parameters, terminal assignments and as-found diagnostics before removal.
Check contamination, corrosion, ventilation, vibration and cabinet temperature before fitting the replacement.
Complete the manufacturer and site acceptance procedure, then retain the as-left result with the maintenance record.
Alternative Names
Technical notes
Rack relationship: Install 146031-01 in the rear I/O position paired with the matching 3500/22M TDI front module.
Network relationship: Use the shielded Category 5 10Base-T/100Base-TX copper link, preserve rack addressing and prove host communication after replacement.
Technical reference: Bently Nevada 3500/22M Transient Data Interface Module Datasheet 161581 Rev. AC.
FAQ View All FAQ
-
How should the network connection of 146031-01 be documented before replacement?Record the rack and slot, RJ-45 cable label, switch port, network settings and System 1 communication path before disconnecting the module.
-
What should be checked if 146031-01 has link but System 1 receives no data?Review TDI status, network identity, switch configuration, routing or firewall policy and the System 1 rack definition before replacing hardware.
-
Why cannot 146031-02 automatically replace 146031-01?The -02 module is 100Base-FX fiber while -01 is 10/100Base-TX copper; the cable plant and network interface are different.
-
How is 146031-01 accepted after installation?Verify link at both ends, stable rack communication, correct network identity and successful live and transient data transfer to the approved host.
-
What evidence should be recorded before replacing 146031-01?Capture the complete nameplate, installed slot or mounting position, companion hardware, wiring identifiers and the accepted operating baseline for the 3500/22m 10base-t/100base-tx i/o module.
-
How should an intermittent fault around 146031-01 be isolated?Separate field wiring, connector, supply, grounding, configuration and host-system causes. Reproduce the symptom under a controlled test and change only one variable at a time.
-
What configuration evidence should be retained after commissioning 146031-01?Retain the hardware identity, firmware or parameter record where applicable, channel assignment, as-left measurements, alarm or diagnostic state and the approved functional-test result.
-
When should 146031-01 be rejected during incoming inspection?Quarantine the item if the complete marking, connector keying, board revision, protective coating, terminal condition or required companion hardware differs from the approved replacement record.
Supporting new and legacy automation
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
Related cases and sourcing guidance
View all case studiesYou May Also Like
Product Browsing History
-
Whatsapp: +86 18030235313
Send us a message. -
sales13@apterpower.com
Complete our online form. -
+86 18030235313
Speak to our team in your native language.






