About Us Contact Us
 
  • Please try to be as accurate as possible with your search.
  • We can quote you on 1000s of specialist parts, even if they are not listed on our website.
  • We can't find any results for “”.
    SEE MORE
      SEE PRODUCTS IN SEARCH PAGE ()
      +86 18030235313 sales13@apterpower.com Fast Quote
      About Us Contact Us +86 18030235313 sales13@apterpower.com Fast Quote
      Get Parts Quote
      Name
      Company *
      Phone *
      Email *
      Address
      City
      State / Province / Region
      Zipcode
      Country
      Quantity *
      Part Number *
      Manufacturer
      Preferred Condition
      Additional Information
      Cancel

      330101-00-52-10-02-05

      8 mm Proximity Probe
      In Stock
      Ships by Wednesday, October 14
      Fast Shipping Available

      Product Describe：

      Bently Nevada 330101-00-52-10-02-05 is an unarmored 3300 XL 8 mm proximity probe with an imperial mounting thread and standard ClickLoc connection. In a matched transducer chain, it supports non-contact monitoring of shaft position and vibration.

      Ask our team:

      Get a quick price for： 330101-00-52-10-02-05
      Quantity*
      Upload (gif, jpg, jpeg, png, bmp, doc, docx, xls, xlsx, ppt, pdf, csv)
      Get a Quote
      For more information on how your data is processed and stored by Apterpower please read our privacy policy.
      Technical specifications Information Technical notes FAQ

      Technical specifications for 330101-00-52-10-02-05

      Technical specifications for 330101-00-52-10-02-05

      • Manufacturer:
        Bently Nevada
      • Product Category:
        Machinery Monitoring System
      • Spare Part Number:
        330101-00-52-10-02-05
      • Estimated shipping dimensions:
        23x23x2cm
      • Weight:
        0.2 kg
      • Tariff Code:
        8537101190
      • Counliy of origin:
        USA
      • Product type:
        3300 XL 8 mm proximity probe
      • Mounting thread:
        3/8-24 UNF-2A
      • Probe armor:
        Without armor
      • Connector and cable:
        Miniature coaxial ClickLoc; standard cable; no connector protector (option 02)
      • Approval option:
        CSA, ATEX and IECEx (option 05; applicability follows installed marking)
      • Nominal probe DC resistance:
        7.59 +/- 0.50 ohm
      • Matched-system frequency response:
        0 to 10 kHz, +0/-3 dB under reference conditions
      • Matched-system scale factor:
        7.87 V/mm (200 mV/mil) nominal under reference conditions
      • Matched Proximitor supply:
        -17.5 to -26 Vdc without barriers; -23 to -26 Vdc with barriers
      • Matched Proximitor output resistance:
        50 ohm
      • Standard calibration target:
        AISI 4140 steel
      View as PDF Ask for Quote

      Information

      Information

      Overview Manuals Common Applications Product Precautions
      Bently Nevada 330101-00-52-10-02-05 is an unarmored 3300 XL 8 mm proximity probe with an imperial mounting thread and standard ClickLoc connection. In a matched transducer chain, it supports non-contact monitoring of shaft position and vibration.
      • Unarmored 330101 probe with imperial 3/8-24 UNF mounting
      • Manufacturer-coded standard probe lead and 3300 XL pairing
      • Standard ClickLoc coaxial connection without a protector
      • Option 05 for CSA, ATEX and IECEx approval markings

      Use the probe only within an approved 3300 XL 8 mm transducer chain with the matched cable path, Proximitor sensor, calibration target and monitoring channel.

      Important Notice: Confirm the complete ordering mark, ClickLoc protection, target calibration and installed approval drawing before commissioning.

      330101-00-52-10-02-05 Manuals & Downloads
      330101-00-52-10-02-05 Technical Reference (PDF)330101-00-52-10-02-05 Installation & Commissioning Guide (PDF)

      The first PDF presents verified probe and matched-system data. The second gives a separate field sequence for installation, checks and acceptance.

      Shaft-relative vibration
      Non-contacting probe input in the matched 3300 XL 8 mm system on fluid-film bearing machinery.
      Shaft position
      Static displacement measurement with the specified conductive target and configured gap.
      Keyphasor reference
      Phase-reference measurement when connected to an approved monitoring channel.
      Speed indication
      Rotational reference in an approved probe/Proximitor/monitor arrangement.
      Before installing this 330101 probe, confirm its unarmored imperial construction, standard ClickLoc option and matched 3300 XL monitoring system against the controlled record.
      1
      Confirm the complete 330101-00-52-10-02-05 ordering code before fitting the probe.
      2
      Confirm the imperial mounting thread and the case option against the existing mounting location.
      3
      Route and support the unarmored lead to avoid bending, abrasion and oil ingress.
      4
      Keep the ClickLoc connector clean and finger-tight; the ordered 02 option has no protector.
      5
      Use a Proximitor and companion cable arrangement matched to the ordered probe option.
      6
      Check the installed target material against the published AISI 4140 calibration basis.
      7
      Set and verify the static gap before accepting the dynamic signal.
      8
      Confirm the applicable 05 approval marking and installation drawing for the actual area classification.

      Technical notes

      Technical notes

      Match the probe, companion cable configuration and Proximitor sensor to the approved monitoring channel. Confirm the AISI 4140 target-calibration basis, clean ClickLoc engagement and controlled probe gap before commissioning.

      FAQS

      • Which mounting thread must the 330101-00-52-10-02-05 installation accept?
        The 330101 ordering family uses a 3/8-24 UNF-2A thread; verify the machine mounting location against this format.
      • What does the 330101 family specify about probe armor?
        The official ordering table identifies 330101 as the unarmored imperial-thread version of the 3300 XL 8 mm probe.
      • How is the probe paired with the rest of its transducer chain?
        The installed probe, any applicable extension cable and the Proximitor sensor must be matched to the ordered system configuration.
      • Which connection is specified by the 02 option?
        It is the miniature coaxial ClickLoc connector with standard cable and without the connector protector.
      • What does the final 05 ordering option designate?
        The datasheet lists CSA, ATEX and IECEx approvals for option 05; confirm applicability from the installed unit marking and the relevant installation drawing.
      • What nominal DC resistance applies to the ordered probe?
        For the ordered cable option, the published center-to-outer-conductor probe resistance is 7.59 +/- 0.50 ohm.
      • What target material underlies the published system accuracy?
        The standard Proximitor is factory calibrated to AISI 4140 steel; the published accuracy and interchangeability limits do not automatically apply to other targets.
      • What should be checked if an older non-XL component remains in the loop?
        The manufacturer permits specified XL/non-XL interchange, but complete-chain performance is then limited to the non-XL system specification.
      Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, modules and cards, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
      Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer`s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

      You May Also Like

      Product Browsing History

      We’re Here When You Need Us

      From product insights to customer service needs, our experienced service team will focus on getting you what you need quickly
      Contact Us

      Enquire

      Complete our online form.
      CONTACT >>

      Call Us

      Speak to one of our team.
      CONTACT >>

      Live Chat

      Send us a message.
      CONTACT >>