With more than 30.000 high-quality spare parts, they can be sold immediately. Our large inventory allows us to quickly meet customer needs, thereby reducing downtime and protecting production schedules. Our timely delivery time provides you with security and save money.
Standard Interconnect Cable
Two-conductor twisted,
shielded 22 AWG cable with two-socket
moisture resistant female connector
at one end, terminal lugs at the other end.
Used with monitors. Not for use with
21128 Velocity Transducer Housing.
The 9571-66 is a standard interconnect cable manufactured by Bently Nevada. This model is commonly used in industrial monitoring systems to connect sensors (such as speed sensors or accelerometers) to monitors or frequency converters.
Superior Noise Immunity
Environmental Resilience
API 670 Compliance
Bently Nevada Velomitor Piezo-velocity Sensors are designed to measure absolute (relative to free space) bearing housing, casing, or structural vibration. The 330500 is a specialized piezoelectric accelerometer that incorporates embedded integrated electronics in a solid-state design. Because the 330500 incorporates solid-state electronics and has no moving parts, it does not suffer from mechanical degradation and wear, and can be mounted vertically, horizontally, or at any other angle of orientation.
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Bently Nevada 9571-66 Standard Interconnect Cable Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description.
Power Generation
Connecting casing sensors to monitor vibration caused by rotor imbalance or bearing failure.
Oil & Gas
Transmitting dynamic casing vibration signals for the mechanical protection of critical units.
Steel & Metallurgy
Ensuring stable acquisition of fan casing vibration data in high EMI environments.
Hydraulic Engineering
Monitoring the velocity response of the turbine head cover or guide bearing housings.
Air Separation
Monitoring the vibration status of integral gear-driven compressor casings.
General Manufacturing
Connecting sensors remotely mounted on fan gearboxes for long-distance signal transmission.
When using the 9571-66 interconnect cable, the focus is on signal integrity and physical protection: ensure the 2-socket MIL connector is fully tightened to maintain its moisture-resistant seal, and strictly follow pin definitions (typically A-Signal, B-Common) to avoid reversed polarity. Since the cable is non-armored PVC, it should be routed through protective conduit to shield against EMI and prevent mechanical damage or prolonged oil exposure. Additionally, ensure the shield is single-point grounded only at the monitoring rack end—never at the sensor end—to avoid ground loop interference and ensure accurate transmission of dynamic vibration data.
It is a 66-foot long, 2-conductor shielded interconnect cable manufactured by Bently Nevada.
What is the primary use of 9571-66?
It is used to connect Velomitor velocity sensors (such as the 330500) to 3500 monitoring racks or junction boxes.
How does 9571-66 connect to the sensor?
It connects via an integral 2-socket moisture-resistant female MIL connector that threads onto the sensor top.
Does 9571-66 belong to the 3300 XL Proximity system?
No. It is a velocity sensor accessory, not a component of the proximity probe system.
Does 9571-66 have stainless steel armor?
No. The 9571 is a non-armored PVC cable; for armor, the 16710 series is typically used.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, modules and cards, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer`s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Videos
News
Applications
